Outback-power-systems FLEXpower TWO Quick Start Guide Manual de usuario descargar pdf

ComponentsMATE3 Programming

IMPORTANT:

Programming should be done by a qualified installer who is trained on programming inverter power systems. Failure to program accurate parameters for the

system could potentially cause equipment damage. Damage caused by inaccurate programming is not covered by the limited warranty for the system.

AC Source

Utility Grid, or

AC Generator

Main Electrical Panel

(or overcurrent device

for the AC source)

Electrical Distribution Subpanel

(Load Panel)

Battery Bank

Photovoltaic (PV) Array

(with PV Combiner Box)

Customer-Supplied

Components

Contact Technical Support:

Telephone: +1.360.618.4363

Email: [email protected]

Website: www.outbackpower.com

IMPORTANT:

Not intended for use with

life support equipment.

> 90% (blinks if charge parameters are met)

Color

Red

Yellow

Green

≥ 80%

≥ 70%

≥ 60%

≥ 60% off, < 60% solid, < 50% blinks

Battery State-of-Charge

FNDC LED Indicators

Phase

Active Error

AC IN

AC OUT

RedYellow

Yellow

Red

Surge Protector LEDs

LED Indicators on the Inverter

Inverter Status LED Indicators

Green

Yellow

Red

Inverter on (solid) or standing by (flash)

AC source in use (solid) or standing by (flash)

Inverter error or warning (see manual)

Green

Yellow

Red

12.5 Vdc or higher

11.5 to 12.4 Vdc

11.4 Vdc or lower

Color

Battery Status LED Indicators

25.0 Vdc or higher

23.0 to 24.8 Vdc

22.8 Vdc or lower

50.0 Vdc or higher

46.0 to 49.6 Vdc

45.6 Vdc or lower

12 V Inverter 24 V Inverter 48 V Inverter

Note: For automatic generator

start features see the MATE3

manual for details.

900-0152-01-00 Rev A.vsd\Page-1\2013-01-17

Inverter/Chargers

(x2)

AC Enclosure Box

FW500-AC

DC Enclosure Box

FW500-DC

System Display and

Controller

MATE3

MATE2

Communications

Manager

HUB10

HUB4

FX Series

VFX Series

GTFX Series

GVFX Series

GFX Series

FLEXnet DC Monitor FNDC

Surge Protector FW-SP-ACA

Remote Temp Sensor RTS

FLEXpower System Products

Major Components

AC Bypass

Assembly

FW-IOBD-120/240VAC

FW-IOBD-120VAC

PNL-175-DC

PNL-250-DC

Inverter Circuit

Breaker

PV8

PV12

Charge Controller

FLEXmax 80

FLEXmax 60

Optional OutBack

Components

PV Combiner Box

Balancing

Transformer

FW-X240

1 2 3 4

Indice de contenidos

Pagina 1 - ComponentsMATE3 Programming

ComponentsMATE3 ProgrammingIMPORTANT: Programming should be done by a qualified installer who is trained on programming inverter power systems. Failu

Pagina 2 - Mounting

Wire Sizes/Torque RequirementsAC Circuit BreakersDC Circuit BreakersDC EnclosureControl Wiring Terminal Block:The Inverter ON/OFF terminals are used f

Pagina 3 - De-energize/Shutdown

Energize/Startup ProceduresPre-startup Procedures:1. Double-check all wiring connections.2. Inspect the enclosure to ensure no tools or debris has bee

Pagina 4 - General Wiring

General WiringOIOIOIOIOIOIOIOIOIOIOIOIMATE RTSAC HOT OUTAC NEUTRAL OUTCHASSIS GROUND/PECHASSIS GROUND/PEAC NEUTRAL INAC HOT INCB3CB2CB1CB6CB5CB4CB8CB7

Comentarios a estos manuales

Sin comentarios

Outback-power-systems FLEXpower TWO Quick Start Guide Manual de usuario

Busca en linea o descarga Manual de usuario para Proveedores De Energía Outback-power-systems FLEXpower TWO Quick Start Guide. Outback Power Systems FLEXpower TWO Quick Start Guide User Manual Manual de usuario

Indice de contenidos

Comentarios a estos manuales

Relacionado con productos y manuales para Proveedores De Energía Outback-power-systems FLEXpower TWO Quick Start Guide